Ductless Zoned Comfort
Zone-by-zone heating and cooling without ductwork, sized correctly for your space from day one.
Common Pitfalls
The most common failures come down to sizing shortcuts and skipped electrical checks, not the equipment itself.
A unit sized by square footage alone ignores ceiling height, window area, and insulation, leaving rooms uncomfortable year-round.
A proper BTU load calculation for each zone accounts for every heat-gain and heat-loss factor in that specific space.
Connecting a head to an existing circuit without checking the electrical load causes nuisance trips and can void equipment warranties.
Each indoor head gets its own dedicated circuit, with breaker rating matched to the equipment’s nameplate requirements.
Stretching a single-zone head across multiple rooms leaves far corners unconditioned and forces the compressor to overwork.
Multi-zone setups assign one indoor head per distinct area, so each room reaches setpoint without overloading the outdoor condenser.
A line set installed without a vacuum and refrigerant pressure check can leak slowly, cutting efficiency and damaging the compressor.
A post-install check confirms refrigerant pressure and BTU output at every zone before the job is signed off.
System Options
From a single garage zone to a whole-home multi-zone setup, the right configuration depends on your floor plan and existing infrastructure.
One indoor head and one outdoor condenser condition a single room or space, starting at 9,000 BTU for smaller areas.
One outdoor condenser powers up to four or more indoor heads, each on its own circuit, for whole-home zoned control.
A dedicated head conditions a new addition independently, without tying into the main home’s existing system.
Single-zone setups sized for the specific heat load of a garage or converted space, including insulation and door area.
Full install from line set routing to electrical hookup.
Swap an existing unit with correctly sized new equipment.
Filter cleaning, coil checks, and refrigerant pressure review.
Fault diagnosis and component-level repair for existing systems.
Why Choose Us
Every step from first contact to final check is documented, so nothing is left to guesswork.
Denver-metro elevation affects system efficiency, so sizing is adjusted before any equipment is recommended.
The written estimate covers equipment, installation scope, permits, and timeline, no surprises after you commit.
The written estimate names the contractor, so you can confirm the right credentials for mini split work in Lakewood before signing.
BTU output and refrigerant pressure are verified at every zone before the installer leaves the property.
Every enquiry starts with a load review and existing equipment check before a single product is specified.
Pricing Estimates
| Configuration | Typical installed cost | Typical use |
|---|---|---|
| Single-zone 9K BTU | $2,200-$3,200 | Small room |
| Single-zone 12K BTU | $3,800-$5,500 | One room |
| Single-zone 24K BTU | $5,200-$7,500 | Large room |
| Dual-zone system | $7,500-$10,500 | Two rooms |
| Three-zone system | $10,500-$14,500 | Small whole home |
| Four to five zone system | $13,500-$25,000 | Whole-home retrofit |
Common Questions
Yes. A mini split heat pump runs in both directions, it moves heat out of your room in summer and pulls heat in during winter. One unit handles both functions without any seasonal swap-out. You control heating and cooling from the same wall-mounted remote or app.
Sizing is determined by a load calculation that accounts for room square footage, ceiling height, window area, insulation, and sun exposure. This calculation runs before recommending any unit. An undersized unit runs constantly without reaching your set temperature; an oversized one short-cycles and leaves the air humid.
A single-zone mini split is designed for one room or open area. Multi-zone systems connect multiple indoor heads to one outdoor unit, covering several rooms from a single installation. Whether one unit or several makes sense depends on your floor plan and how many separate spaces need conditioning.
The installer drills one hole, typically 2.5 to 3 inches, through the wall for the line set, then routes refrigerant lines, a condensate drain, and low-voltage control wiring to the outdoor unit. Line sets are usually run along the exterior wall in a protective conduit channel. Interior wall work is minimal.
Yes. The full installation scope covers mounting the indoor head, placing the outdoor unit, running and insulating the line set, making electrical connections, and completing a post-install performance check. The written estimate you receive before booking itemizes every part of that scope.
Guide prices run from $2,200-$3,200 (Single-zone 9K BTU) to $13,500-$25,000 (Four to five zone system). Multi-zone systems and longer line-set runs add the most to the total.
Yes. If your panel lacks a suitable breaker slot, a new dedicated circuit is required and adds to the total. Extra line-set length, a wall-mount bracket for the outdoor unit, or conduit for exposed exterior runs can also increase the cost. The itemised written estimate covers these before any work begins.
A post-install performance check is completed after every installation to confirm the system reaches set temperatures and shows no refrigerant or condensate issues. If a problem surfaces after that check, a return visit is scheduled to diagnose and correct it. Scheduling a heat pump inspection can also catch issues early.
We cover Mini Split Heat Pumps in and around Lakewood, including Arvada, Colorado, Bear Creek, Colorado, Belmar, Colorado, Edgewater, Colorado, Golden, Colorado, Denver, Colorado, Wheat Ridge, Colorado, Littleton, Colorado, Morrison, Colorado, Ken Caryl, Colorado and Columbine, Colorado. If your area isn’t listed, send us a quick message to check.
Describe your setup and we’ll schedule an on-site assessment and put the full scope in writing before anything is booked.