Skip to content

About

About Lakewood Heat Pumps

We arrange local heat pump installers for Lakewood-area homes, with a written scope before anything is booked.

A heating engineer works on an outdoor air source heat pump or air conditioning unit with a power drill.

How We Work

A structured process, not a guess based on square footage

Every enquiry follows the same steps so nothing is scoped after the work has already started.

Lakewood Heat Pumps is a Lakewood-area enquiry service for heat pump installation, maintenance, repair and replacement. We take your enquiry and schedule the on-site work. Tell us about your home and we schedule an on-site assessment, a load calculation, and put the full scope in writing before anything is booked.

Sizing a heat pump in the Denver metro is not the same as sizing one at sea level. Altitude derating reduces rated efficiency, and the wide day-to-night temperature swings here demand a cold-climate performance review as part of every assessment. The installer we arrange will factor those conditions into the system recommendation, not apply a generic square-footage rule.

The written estimate you receive before any work is scheduled covers equipment selection, installation scope, electrical and duct requirements, freeze protection for outdoor lines, and permitting. Permit requirements vary across Denver metro counties and municipalities, so they are identified and included in the scope from the start, not discovered mid-job.

Once installation is complete, a post-install performance check confirms the system heats and cools to its rated output before the job is closed out. Our mission is straightforward: take the guesswork out of heat pump installation so you know exactly what the work involves and what it will cost before you commit.

Our Mission

“We exist to take the guesswork out of heat pump installation for Lakewood-area homeowners by arranging a written scope, altitude-adjusted sizing, and a post-install performance check before anything is signed off.”

  1. Transparency

    Written, itemised estimates before any work is scheduled, no surprise costs.

  2. Accuracy

    Altitude-adjusted load calculations drive every system recommendation.

  3. Completeness

    Permits, electrical needs, and duct changes are scoped upfront, not discovered later.

  4. Verification

    A post-install check confirms the system performs as specified before closeout.

The Process

From your first enquiry to a confirmed install

Request an Assessment

  1. Describe Your Home

    Tell us your square footage, current heating setup, and any known issues. The more detail you share, the more accurate the initial assessment.

  2. Arrange an Assessment

    We schedule an HVAC site visit, a load calculation, and a review of altitude-adjusted sizing for your elevation.

  3. Review the Written Scope

    You receive an itemised written estimate covering equipment, installation scope, permits, electrical needs, and timeline before any work is scheduled.

  4. Confirm & Install

    Once you approve the scope, the installer schedules the work. Permitting is handled as identified in the estimate, with no surprises mid-job.

  5. Post-Install Check

    After installation, a performance check confirms the system reaches its rated output. The job is not closed out until that check is complete.

Common Questions

What to expect when you use Lakewood Heat Pumps

  • Do you do the installation work yourselves?

    No. We schedule all on-site work. Our role is to size your property correctly and make sure you have a written scope before anything is scheduled.

  • Why does altitude matter for heat pump sizing in Lakewood?

    Heat pumps are rated at sea level. Above 5,000 ft, a unit delivers less capacity than its nameplate suggests. Lakewood sits in that range, so the load calculation is adjusted for elevation to avoid an undersized system that can’t keep up on cold nights.

  • What does the written scope include?

    The itemised estimate covers equipment model and specs, installation labor, any duct or electrical changes required, permitting fees applicable to your municipality, and a project timeline. You see all of that before a booking is confirmed.

  • What happens if I skip the property assessment and just pick a system size?

    An oversized unit short-cycles and wears out faster. An undersized one runs constantly and still can’t meet demand on the coldest nights. Either outcome costs more over time than the assessment itself. Skipping it is the most common reason heat pump installs underperform.

  • Which heat pump types can you arrange?

    We arrange installation, maintenance, repair, and replacement for air-source, mini-split, and geothermal heat pump systems. The assessment determines which type fits your property’s layout, lot size, and heating load.

  • Do permits vary across the Denver metro?

    Yes. Permitting requirements differ by county and municipality across the metro. The installer factors the applicable permit requirements into your written scope from the first assessment, so there are no surprises after work begins.

At a glance

Business details

Business name
Lakewood Heat Pumps
About
An older furnace or air conditioner that is due for replacement leaves you weighing a heat pump against what you have. Lakewood Heat Pumps asks about the system and the rooms it serves, schedules the visit and follows up. A written estimate arrives before work begins. Send us your system details.
Contact
1 720-936-7533 · contact@lakewoodheatpumps.com
Areas covered
Lakewood and 11 more areas

Tell Us About Your Home

Every enquiry starts with a written scope and altitude-adjusted sizing review, so you know exactly what the install involves before you commit.

Step 1/2