---
title: "Heat Pump Inspection in Lakewood | Lakewood Heat Pumps"
description: "Choosing the wrong system size or skipping a load calculation costs money every month. We arrange a local heat pump inst"
canonical: "https://www.lakewoodheatpumps.com/services/heat-pump-inspection"
lastmod: "2026-11-15T10:04:32.711Z"
---

# Heat Pump Inspection in Lakewood

![Clean air conditioning condenser coil after service cleaning backyard](https://utmost-ibex-736.convex.cloud/api/storage/bbe53480-ac74-4638-a717-931b252b2ab9)

Know exactly what your system is doing, and whether to repair or replace it, before cold weather forces the call.

- **Written Findings**: Every inspection ends with a written summary of measured results.
- **Repair or Replace**: You get a clear recommendation based on actual readings, not guesswork.
- **On-Site Assessments**: We schedule an on-site assessment of your property.
- **All System Types**: Air-source, mini-split, and geothermal systems all covered.

## Where a rushed or incomplete inspection leaves you worse off

A surface-level check misses the measurements that actually tell you what the system is doing.

- **Skipped Pressure Test**: Without a refrigerant pressure reading, a low charge goes undetected and the compressor runs under stress until it fails.
  **Measured Refrigerant Check**: Superheat and subcooling values are measured against the manufacturer’s spec to confirm the charge is correct.
- **Missed Reversing Valve**: A reversing valve that sticks in one mode means the system heats when it should cool, or vice versa, and the fault is easy to overlook visually.
  **Valve Operation Test**: The reversing valve is tested through both modes to confirm it switches cleanly and holds position under normal operating pressure.
- **No Electrical Draw Test**: A capacitor or contactor near failure draws abnormal current but shows no visible damage, so a visual-only check leaves the risk in place.
  **Amp Draw Measurement**: Blower motor amp draw and contactor condition are tested against rated values to catch components that are failing before they cause a shutdown.
- **Vague Outcome Report**: A verbal summary after the visit gives you no basis for comparing repair cost against replacement cost when the next failure happens.
  **Written Condition Summary**: You receive a written record of every measurement taken, what is within spec, and what is not, so any repair decision is grounded in data.

## What the inspection covers

Each check targets a specific component or circuit where a hidden fault can cut efficiency or cause a breakdown.

- **Refrigerant Pressure & Charge Check**: Superheat and subcooling are measured to confirm the refrigerant charge is within the manufacturer’s specified range.
- **Evaporator & Condenser Coil Inspection**: Both coils are checked for fouling, fin damage, and airflow restriction that reduce heat transfer and raise energy draw.
- **Electrical Contactor & Capacitor Testing**: Contactor pitting and capacitor microfarad readings are checked to catch components that are close to failure.
- **Blower Motor Amp Draw Test**: Measured amp draw is compared to the motor’s rated current to identify a motor running outside its normal operating band.
- **Reversing Valve & Defrost Control Check**: The reversing valve is cycled through both modes and the defrost control is tested to confirm reliable cold-weather operation.
- **Condensate Drain & Thermostat Calibration**: The condensate drain is checked for blockage and the thermostat’s calibration is verified against actual supply air temperature.

- **Ductwork Airflow Assessment**: Airflow measured at the air handler to catch restrictions.
- **Heating-Season Readiness Check**: Full system check timed before Lakewood’s cold months.
- **Repair-or-Replace Recommendation**: Written recommendation based on measured findings.

## What a heat pump inspection covers and what you get at the end

A structured inspection measures actual system performance and gives you a clear picture before a failure forces the decision.

The inspection works through the system in a set sequence. The indoor unit check covers the evaporator coil, condensate drain, blower motor amp draw, and thermostat calibration. The outdoor unit check covers the condenser coil condition, electrical contactor and capacitor testing, and refrigerant pressure against the manufacturer’s specification. Lakewood’s cold winters make heating-season readiness a practical priority, and older housing stock in the area often has aging systems that benefit from a condition assessment before a failure occurs.

The refrigerant circuit is checked for superheat and subcooling values, which reveal whether the charge is correct and whether the reversing valve is switching cleanly between heating and cooling modes. A defrost control cycle test confirms the outdoor unit can shed ice buildup during cold weather. Ductwork airflow is assessed at the air handler to catch restrictions that reduce system output without triggering a fault code.

At the end of the inspection, you receive a clear summary of what was measured, what is within spec, and what is not. That summary supports a repair-or-replace recommendation with specific findings rather than a general opinion. If a repair is needed, the scope is identified so you can make an informed decision before any work is authorised.

[Request an Assessment](https://www.lakewoodheatpumps.com/contact)

## Why Lakewood Heat Pumps for a heat pump inspection?

Accountability and process, not just a technician showing up and looking around.

- **Written Estimate Before Any Work Is Booked**: Every enquiry produces an itemised written estimate covering scope and timeline before a visit is confirmed.
- **System Evaluation Comes First**: We start with a review of the existing equipment’s condition, not a sales conversation about replacement options.
- **On-Site Assessments, Scheduled for You**: We schedule an assessment built around the Colorado Front Range climate and its demands on heat pump systems.
- **Post-Inspection Check on Findings**: A post-visit review confirms the written summary matches what was measured, so nothing is left as a verbal impression.
- **Air-Source, Mini-Split & Geothermal Coverage**: Every visit covers all three system types, so the scope matches your actual equipment rather than a single product line.

## From first enquiry to written findings

1. **Describe Your System**: Tell us your system type, age, and the symptoms you have noticed so the right checks are prioritised from the start.
2. **Book the Inspection**: We schedule a visit that runs the full checklist and records every measurement against the manufacturer’s specification.
3. **Receive Your Written Report**: You get a clear summary of findings and a repair-or-replace recommendation before any follow-on work is discussed or authorised.

[Request an Assessment](https://www.lakewoodheatpumps.com/contact)

## Typical Heat Pump Inspection Prices

| Inspection type | Typical cost | Typical duration |
| --- | --- | --- |
| Basic inspection | $150-$250 | 1-2 hours |
| Full system evaluation | $200-$350 | 2-3 hours |
| Pre-repair diagnostic | $150-$300 | 1-2 hours |

These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.

[See all prices](https://www.lakewoodheatpumps.com/pricing)

## Questions about heat pump inspections in Lakewood

### Why is my heat pump running but my house still does not feel comfortable?

A running heat pump that fails to heat or cool properly usually points to low refrigerant, a dirty coil, a failing compressor, or a duct leak bleeding conditioned air before it reaches the rooms. An inspection checks each of these in sequence, so the actual cause gets identified rather than guessed at.

### Do heat pumps need to be inspected?

Yes. Heat pumps run year-round as both heater and air conditioner, so components wear faster than a system used only one season. Regular inspections catch refrigerant loss, coil fouling, and electrical faults early, before they become breakdowns. Skipping checks is the most common reason systems fail ahead of their expected lifespan.

### How often should a heat pump be checked?

Once a year is the standard minimum, but twice a year, once before the heating season and once before cooling season, is better for a system that runs continuously. Annual checks catch wear before it becomes a fault; twice-yearly checks also confirm the reversing valve and defrost cycle are ready for the next season.

### What does a heat pump inspection usually look at?

A thorough inspection covers refrigerant charge, coil condition on both the indoor and outdoor units, electrical connections and capacitors, airflow and filter restriction, thermostat calibration, defrost cycle operation, and the condition of the reversing valve. The technician also checks for unusual noise or vibration that signals mechanical wear.

### Will an inspection tell me if my heat pump needs repair or replacement?

Yes. An inspection gives you a clear picture of the system’s current condition, remaining component life, and any active faults. With that information you can weigh the cost of repair against the age and efficiency of the unit and make a grounded decision rather than guessing. [See repair vs. replacement options](https://www.lakewoodheatpumps.com/services/heat-pump-replacement).

### Does an inspection mean my heat pump needs replacement?

No. Most inspections find minor issues, a dirty coil, a loose connection, low refrigerant, that are straightforward to fix. Replacement only comes up when the inspection reveals a failed compressor, severe refrigerant loss from a cracked component, or a system old enough that repair costs outweigh the value of keeping it.

### How much does it cost to get my heat pump inspected?

Guide prices run from $150-$250 (Basic inspection) to $200-$350 (Full system evaluation). A written scope is provided before any work is booked, so there are no surprise charges on the day.

### How much does a heat pump survey cost?

Guide prices run from $150-$250 (Basic inspection) to $200-$350 (Full system evaluation). The price covers a full condition assessment of the system, with a written summary of findings. Complex systems, such as multi-zone mini-splits or geothermal loops, may sit toward the higher end of that range.

### Which areas do you cover for Heat Pump Inspection?

We cover Heat Pump Inspection in and around Lakewood, including Arvada, Colorado, Bear Creek, Colorado, Belmar, Colorado, Edgewater, Colorado, Golden, Colorado, Denver, Colorado, Wheat Ridge, Colorado, Littleton, Colorado, Morrison, Colorado, Ken Caryl, Colorado and Columbine, Colorado. If your area isn’t listed, [send us a quick message](https://www.lakewoodheatpumps.com/contact) to check.

## Get a Clear Answer on Your Heat Pump’s Condition

Describe your system and we’ll schedule a full inspection and deliver the findings in writing before any work is booked.

[Request an Assessment](https://www.lakewoodheatpumps.com/contact)

## Business details

### Contact

- **Phone**: [1 720-936-7533](tel:1720-936-7533)
- **Email**: [contact@lakewoodheatpumps.com](mailto:contact@lakewoodheatpumps.com)
- **Based in**: Lakewood, CO, 80214
- **Enquiries**: [Send an enquiry](https://www.lakewoodheatpumps.com/contact) — We ask for your name, phone number, email and a message.

### Opening hours

- **Monday**: 08:00 – 18:00
- **Tuesday**: 08:00 – 18:00
- **Wednesday**: 08:00 – 18:00
- **Thursday**: 08:00 – 18:00
- **Friday**: 08:00 – 18:00
- **Saturday**: 10:00 – 16:00
- **Sunday**: 10:00 – 16:00
